Chamberlain RESIDENTIAL GATE OPERATOR GA420D Bedienungsanleitung

RESIDENTIAL GATE OPERATORModels GA400D and GA420DFor Residential Use OnlyThe Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.c

Check Your GateGate MUST swing freely and be supported entirely by its hinges.Remove ANY/ALL wheels from the bottom of gate.Gate MUST NOT hit or drag

Gate TravelDetermine how your gate is to be opened. 11 Preparation and OverviewPull-to-OpenPush-to-OpenInside PropertyInside PropertyOutside Propert

Typical Tubular Metal GateTypical Tubular Metal GateTypical Wood GateTypical Wood GateTypical Farm/Ranch GateTypical Farm/Ranch GateTypical Chain Link

INSTALLATIONAttach Operator to Gate 13 InstallationIdentify Hinge TypeThe illustrations below show common gate hinges. There are many styles of hinges

Installation 14Measuring and Marking for the Gate BracketBefore proceeding, begin with the gate in the fully closed position. There are two methods de

15 InstallationPosition the Extension Bracket to Post BracketHold post bracket in desired position. Align extension bracket to a position as CLOSE AS

“Slowly extend the piston 1/4" (.64 cm) from collar and draw a mark.”THIS SIDETO GATEScrewsRemove Motor AssemblyRemove screws (4) and remove moto

17 InstallationPosition Gate BracketHold the gate operator against the gate. The gate operator (arm) must be level. Clamp bracket to gate. Some insta

Check Piston TravelVisually check the clearance. Holding the gate firmly, slowly walk the gate to the fully open position. Check for pinch points at t

19 InstallationSecure the post bracket to gate post using hardware. The gate operator (arm) must be level.Secure Gate Bracket to GateRemove the opera

Introduction 2TABLE OF CONTENTSWhen you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of se

Moving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime without prior warning.Do not let children operate the gate orplay in the gate

21 InstallationThe control box MUST be mounted within 5' of the gate operator. Mount the control box as high as possible for best radio receptio

Mount the Control BoxSecure the control box to mounting surface (post, wall, column, etc.) using appropriate hardware(not provided).Install the Contro

Moving Gate Can Cause Moving Gate Can Cause Injury or Death Injury or Death KEEP CLEAR! KEEP CLEAR! Gate may move at any Gate may move at any time wit

Wiring 24Connect Operator to Control BoardExtend operator cable and wires to GATE 1 connector and connect as shown. Tighten watertight connector nut.M

Occasionally in dual gate installations, one gate would need to open first and close second. This would happen if there was an ornamental overhang on

Connect second Operator to Control Board (Model Ga420D Only)• Before digging, contact local underground utilitylocating companies.• Trench across dr

27 WiringJunction BoxThe following items are required to complete the junction box (not provided) installation:• 4 x 4 Junction Box with 3/4 NPT thre

Secure Junction BoxPut wires inside of junction box. Secure operator and extension cables with watertight nut. Reinstall cover.Connect Wires in Juncti

29 WiringMoving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime without prior warning.Do not let children operate the gate orplay i

Operator SpecificationsMain Supply (Motor) 12Vdc Battery run. Operational between 11.5Vdc and 14.5Vdc.Accessory Power 12V nominal Class II battery

Wiring 301818R93L1L1K2K2Z22Z22P1P1F2F2MOV1MOV1D1D1Q12Q12U4U4OFFOFF MAXMAXOPENSINGLE BUTTONRESETSTOPCHGROVLDCTRL PWRCOMD129D129Z4Z4U3U3D2D2D44D44C11C11

31 WiringConnect BatteriesThe batteries are charged in circuit by using the transformer (provided).Locate the two white battery plugs on the left-han

Test the limits by pressing the SBC to open and close the gate.NOTE: If the SET OPEN LIMIT LED is still blinking, the limits were not programmed succe

NOTES: • If one gate is overlapping the other, the gate that is overlapping must be connected to GATE 1 so it will start moving before the other gate

Force/Timer to Close/Party Mode ControlsWithout a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY

Z22 R91 CLOSE EDGE R94 R92 R93 L1 R1 R2 Z1 K5 K6 K2 F3 10A 32V D1Ø OPEN EDGE/ PHO T O OPEN PHO T O CLOSE PHO T O R227 R2Ø7 Z2 Ø R223 P1 Z9 Z8 F2 F6 D4

Operation and Maintenance 36Using Your Gate OperatorYour operator will operate with up to nine Security✚® remote controls and one Security✚® Keyless

Release PinGate Bracket 37 Operation and MaintenanceManual ReleaseIn case of a power failure, the operator can be disengaged from the gate. Follow t

Operation and Maintenance 38* Class 2 circuit 15 v maximum output 2. Close edge 3. Open edge/photo eye 4. Open photo eye 5. Close photo eye 6. C

39 Operation and MaintenanceYour gate operator is programmed with self-diagnostic capabilities. The diagnostic LED will flash a number of times the

Introduction 4 1. READ and FOLLOW all instructions. 2. The gate operator is intended for use with Class I vehicular swing gates. Class I denotes a

Operation and Maintenance 40SYMPTOM POSSIBLE SOLUTIONOperator does not run. • Power not connected. Make sure the AC/Solar input is connected and th

41 Operation and MaintenanceSYMPTOM POSSIBLE SOLUTIONThe arm moves but cannot • Arm does not extend or contract enough during travel. The arm pist

Operation and Maintenance 42SYMPTOM POSSIBLE SOLUTIONGate opens but does not • An open input is continuously activated. Check the open loop or vehi

43 Operation and Maintenance364215ITEM PART # DESCRIPTION QTY 1 K1A6426 Control Board withMounting Bracket 1 2 K23-19380 Reset Switch 1 3

Operation and Maintenance 441 2 ITEM PART # DESCRIPTION QTY 1 K-41ADBL-0004 Arm Cover 1 2 K-LA-6 Complete Arm AssemblyIncludes: Arm, Motor an

OPEN OPENCLOSEOPEN OPENCLOSEOPEN OPENCLOSE 45 Operation and MaintenanceOPEN OPENCLOSE940D956D953DAutomatic Gate Lock:Solenoid-driven lock that autom

Warranty 46HOW TO ORDER REPAIR PARTSOUR LARGE SERVICE ORGANIZATION SPANS AMERICAINSTALLATION AND SERVICE INFORMATIONCALL OUR TOLL FREE NUMBER1-866-826

NOTES 47 Notes

© 2009, The Chamberlain Group, Inc.01-33859D All Rights ReservedTEMPLATE FOR POST BRACKET MOUNTING132451324553/4"53/4"

5 IntroductionTo prevent SERIOUS INJURY or DEATH from a moving gate:• Install warning signs on the front and back of the gate in PLAIN VIEW.• Perma

Carton InventoryThis operator comes with the hardware to install on a gate that pulls-to-open. If your application requires the gate to be pushed open

All Models: SAFETY SENSORSThe Safety Sensors, model 916GA, are intended for installation with the operators covered in this manual.To order call: 1-86

Moving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime without prior warning.Do not let children operate the gate orplay in the gate

9 Preparation and OverviewDual Gate OverviewOutside PropertyInside PropertyMoving Gate Can CauseInjury or DeathKEEP CLEAR! Gate may move at anytime