Chamberlain SECURITY+ 6200-2K Bedienungsanleitung

The Chamberlain Group, Inc.A DUCHOSSOIS ENTERPRISE845 Larch AvenueElmhurst, Illinois 60126-1196®Complies with UL324 Regulationseffective January 1,Gar

Assembly Step 4Install the Chain/Cable & Attach the Sprocket Cover OpenerSprocket Install Chain & Cable Chamberlain '928/22/90 - 3/6/

• Spin the inner nut and lock washer down thethreaded shaft, away from the trolley.• To tighten the chain, turn outer nut in the directionshown. As yo

• Open your door to the highestpoint of travel as shown. Drawan intersecting horizontal lineon the header wall 2" abovethe high point. This heig

DoorHighest Pointof TravelHeaderWallPivotDistanceHeader WallHighest Pointof TravelDoorDistanceJambHardwareThe Chamberlain Group, Inc.Position Hea

Lag Screws5/16"x9x1-5/8"HighestPoint of Travel(of Garage Door)VerticalCenterLineHeaderWallGarageDoorMounting New Header Bracket10/

HeaderBracketTemporarySupportHeader WallGarageDoorThe Chamberlain Group, Inc.CGI - Attach Tee Rail to Header Bracket2/4/92 - 4/9/92 - 5/3/92 -5/5

Installation Step 4Position the OpenerFollow instructions which apply to your doortype as illustrated.To prevent damage to steel, aluminum,fiberglass

Installation Step 5Hang the OpenerTwo representative installations are shown.Yours may be different. Hanging brackets shouldbe angled, Figure 1, to pr

18Installation Step 6Install the Multi-FunctionDoor Control Panel6ABx1-1/4" ScrewMulti-Function Door ControlInsulated StaplesDry Wall AnchorsScre

LensGuideLensTabLensSlot75 Watt(Maximum)Light BulbThe Chamberlain Group, Inc.STEP 7 Install Lights and Lenses - CGI10/7/91 - 5/2/92 - 5/26/92Le

Start by reviewing these important safety alert symbols: 2Contents PageA review of safety alert symbols . . . . . . . . . . . . . .2You'll need

To reduce the risk of electric shock, your garagedoor opener has a grounding type plug with a thirdgrounding pin. This plug will onlyfit into a groun

The safety reversing sensor mustbe connectedand aligned correctly before the garage dooropener will move in the down direction. This is arequired safe

1/4 x 1-1/2"Lag Screw#10 - 32 x 3/8"Screw1/4" - 20Lock Nut#10 x 32Lock NutStaples1/4" - 20 x 1/2"Carriage Bolts Inst

Invisible Light BeamProtection AreaSensorSensorConnect Wire toOpener TerminalsThe Chamberlain Group, Inc.Attaching Sensor to "C" Wrap and

Installation Step 11Fasten Door Bracket Follow instructions which apply to your doortype as illustrated below or on page 25.To prevent damage to stee

All ONE-PIECE Door Installation Procedure• Center the bracket on the top of the door, in linewith the header bracket as shown. Mark holes.• Drill 5/16

Installation Step 12 Connect Door Arm to TrolleyFollow instructions which apply to your doortype as illustrated below and on page 27.Make sure garage

Door Arm to Trolley 1 pc1/96Nuts5/16"-18LockWashers5/16"RingFastenerStraightArmScrews5/16"-18x7/8DoorBracketClevis Pin5/16&quo

Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until thesafety reversing sensors are completelyinstalled. 28Limit ad

Adjustment Step 2Adjust the ForceToo much force on the door will interfere withthe proper operation of the safety reversesystem. The door might not r

PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 7/16" Socketsand WrenchDrillTape Measure21StepladderPencil3/1

Adjustment Step 4Test the Safety Reverse SystemTest: • Place a one-inch board (or a 2x4 laid flat) on thefloor, centered under the garage door.• Oper

The remote control transmitterThe opener must learn the code of any new remotecontrol. Page 33 explains how to program yourreceiver and how to erase a

32TrolleyTrolleyRelease ArmNOTICEManualRelease Handle(Pull Down)TrolleyTrolleyRelease ArmNOTICEManualRelease Handle(Pull Down & BackTowards Opener

Receiver and Remote Control ProgrammingChildren operating or playing with a garagedoor opener can injure themselves or others.The garage door could cl

1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light,check the fuse box or the circuit breaker. (Some outlet

Having a Problem? (continued)Situation Probable Cause & SolutionThe opener strains ormaximum force isneeded to operatedoor:The door may be out of

7UPCEILING MOUNT ONLY91011NOTICE561413121581432LOCKLIGHT213345567RAIL GREASENO. 83A48Repair PartsRail Assembly Parts Installation Parts 36KEY PARTNO.

Repair PartsOpener Assembly Parts KEY PARTNO. NO. DESCRIPTION1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assemblyComplete with:Spring washerT

LOCKLIGHTLOCKLIGHTAccessories Available for your Opener953CB7702CBSECURITY✚ Multi-FunctionRemote Control:Includes visor clip.Outside Quick Release:Req

IndexAccess Door/Outside Quick Release Accessory...4, 5Chain

4 You may find it helpful to refer back to this page asyou proceed with the installation of your opener.Safety Reversing SensorHorizontal and vertica

CHAMBERLAIN SERVICEIS ON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND SERVICE INFORMATION IS ASNEAR AS YOUR TELEPHONE SIX DAYS A WE

Safety Reversing SensorFINISHED CEILINGSupport bracket& fasteninghardware is required.See page 17.Slack in chain tensionis normal whengarag

Cable PulleyBracket2-Conductor Bell Wire White & White/RedTrolleyDoor BracketHeader BracketHanging BracketsChain and Cable inDispensing CartonCur

HardwareSeparate all hardware from the packages in the rail carton and the opener carton as shown below, for theassembly and installation procedures.L

8 Assembly Step 1Assemble the T-rail & Attach the Cable Pulley BracketHex Screws5/16"-18x7/8"Cable PulleyBracketBracket & Rail Mu

Hardware ShownActual SizeAssembly Step 2Install the Trolley on the T-rail• Place the opener on packing material to protect thecover. For convenience,