Chamberlain 3585S 3/4 HP Bedienungsanleitung

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.liftmaster.comGARAGE DOOR OPENERModel 3585S 3/4 HPFor Residential Use Only

HeaderBracketBelt PulleyBracketTemporarySupportHeader WallGarageDoorClevis Pin5/16"x2-3/4"Ring FastenerHeader BracketBelt PulleyBracketRailC

11ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an idealdoor-to-rail distance. • Remove foam packaging.• Raise the opener

12INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1)

13INSTALLATION STEP 6Install the Door ControlLocate door control within sight of door, at a minimum height of 5' (1.5 m) where small children can

14INSTALLATION STEP 7Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is i

15INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run the opener at this time.To reduce the risk of electric shoc

16Facing the door from inside the garageINSTALLATION STEP 10Install The Protector System®The safety reversing sensor must be connected and aligned cor

17INSTALLING THE BRACKETSBe sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the ga

Invisible Light BeamProtection AreaSafety Reversing SensorSafety Reversing SensorConnect Wire toOpener Quick-Connect TerminalsBell WireBell WireFinish

19Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacture

2Introduction 2-5Safety symbol and signal word review. . . . . . . . . . . . . . . 2Preparing your garage door . . . . . . . . . . . . . . . . . . . .

Header WallVerticalCenterline ofGarage DoorFinished Ceiling OptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expos

21INSTALLATION STEP 12Connect Door Arm to TrolleyFollow instructions which apply to your door type as illustrated below and on the following page.SECT

22ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (

23ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

24ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the a

25Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage

26OPERATIONIMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:Using Your Garage Door OpenerYour Security✚® opener and hand-held

27Using the Wall-Mounted Door ControlTHE SMART CONTROL PANELTMPress the push bar to open or close the door. Press again to reverse the door during the

The 3V2016 lithium batteries for the opener and LED lights (marked “LED and Opener Battery”) should last 5 years. The 3V2450 lithium battery for the p

29CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may cause some minor changes in door operation requiring some re-adjustments, part

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at

30HAVING A PROBLEM?1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned co

Bell WireSafety Reversing SensorKG 1 3 9 7 5 KG 1 3 9 7 5 DiagnosticsLocated OnMotor Unit"Learn" Button LED or Diagnostic LED Installe

32Meaning: This message will appear if the Safety Reversing Sensors are out of alignment, if they are blocked or if the wiring is disconnected. To cle

33*3-Button Remotes (315MHz)If provided with your garage door opener, the large button is factory programmed to operate it. Additional buttons on any

34To Add, Reprogram or Change a Keyless Entry PINNOTE: Your new Keyless Entry must be programmed to operate your garage door opener.USING THE “LEARN”

2451367811126NOTICEUPCEILING MOUNT ONLY9715101314LOCKLIGHT342Installation PartsRail Assembly Parts35REPAIR PARTSKEY PART NO. NO. DESCRIPTION1 4A10

36Motor Unit Assembly PartsDNUPBrownWire(Down)ContactLIMIT SWITCH ASSEMBLY GreyWireYellowWire(Up)ContactCenter LimitContactDriveGear2 4 3 1 15 19 817

37ACCESSORIES 370LM41A52811702LMOutside Quick Release:Required for a garage with NO access door. Enables homeowner to open garage door manually from o

38NOTES

39NOTES

FINISHED CEILINGSupport bracket& fasteninghardware is required.See page 12.SafetyReversing SensorHeaderWallAccess DoorSafety Reversing SensorGap b

© 2008, The Chamberlain Group, Inc.114A3616B All Rights ReservedLIFTMASTER® SERVICE IS ON CALLOUR LARGE SERVICE ORGANIZATION SPANS AM

5Your garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below. Accessories will depend on the model

To avoid SERIOUS damage to opener, ONLY use bolts/fasteners mounted in top of motor unit.ASSEMBLY STEP 1Attach the Rail to the Motor UnitTo avoid inst

7INSTALLATIONIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNINGWARNINGWARNINGWARNING1. READ AND FOLLOW ALL INSTA

8INSTALLATION STEP 1Determine the Header Bracket LocationInstallation procedures vary according to garage door types. Follow the instructions which ap

Lag Screw5/16"-9x1-5/8"HARDWARE SHOWN ACTUAL SIZELag Screws5/16"-9x1-5/8"Highest Point of Garage Door TravelVerticalCenterline ofG