Chamberlain 995XD Bedienungsanleitung

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENERModel 995XD 1/2 HPFor Residential Use Onl

Rail Sprocket RailAssemblyCoupling Motor Unit Bracket Motor Unit Sprocket Foam Packaging Hex Bolts 1/4-20x7/16" Hex Bolts 1/4-20x7/16" Arrow

11INSTALLATIONIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNINGWARNINGWARNING1. READ AND FOLLOW ALL INSTALLATION

12INSTALLATION STEP 1Determine the Header BracketLocationInstallation procedures vary according to garage doortypes. Follow the instructions which app

13INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wallabove the garage door, or to the ceiling. Follow th

14INSTALLATION STEP 3Attach the Rail to the Header Bracket• Position the opener on the garage floor below theheader bracket. Use packing material as a

15Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac

16DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL

MOUNTING AND WIRING THE SAFETY SENSORS• Slide a 1/4"-20x1/2" carriage bolt head into the slot oneach sensor. Use wing nuts to fasten sensors

18ONE-PIECE DOOR WITHOUT TRACKA 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging.• Raise the opener o

MeasureDistanceLag Screws5/16"-18x1-7/8"StructuralSupportsBracket(Not Provided)Lag Screws5/16"-18x1-7/8"(Not Provided)Bolt 5/16&qu

2TABLE OF CONTENTSIntroduction 2-7Safety symbol and signal word review . . . . . . . . . . . . . . .2Preparing your garage door . . . . . . . . . . .

INSTALLATION STEP 7Install the Door ControlLocate door control within sight of door at a minimumheight of 5 feet (1.5 m) where small children cannot r

21INSTALLATION STEP 8Install the Lights • Press the release tabs on both sides of lens. Gentlyrotate lens back and downward until the lens hinge isin

22INSTALLATION STEP 10Electrical RequirementsTo avoid installation difficulties, do not run theopener until Step 11 below.To reduce the risk of electr

23INSTALLATION STEP 12Fasten the Door Bracket Follow instructions which apply to your door typeas illustrated below or on the following page.A horizon

24Header WallVerticalCenterline ofGarage DoorFinished CeilingOptionalPlacementof DoorBracketHeaderBracketDoorBracket2x4 SupportFor a door with no expo

25INSTALLATION STEP 13Connect Door Arm to TrolleyFollow instructions which apply to your door type asillustrated below and on the following page.SECTI

26ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 4:• Fasten the straight and curved door arm sectionstogether to the longest possible length (wit

27ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which thedoor will stop when moving up or down

28ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the back panelof the motor unit. Force adjustment settings regulate theamo

29Without a properly installed safety reversal system, persons(particularly small children) could be SERIOUSLY INJUREDor KILLED by a closing garage do

3PliersWire CuttersClaw HammerHack SawScrewdriverAdjustable End Wrench1/2" and 3/8" Socketsand WrenchDrillTape Measure21StepladderPencil3/16

30OPERATION Using Your Garage Door OpenerYour Security✚®opener and hand-held remote controlhave been factory-set to a matching code which changeswith

31To Open the Door ManuallyDISCONNECT THE TROLLEY:The door should be fullyclosed if possible. Pull downon the emergency releasehandle (so that the tro

32CARE OF YOUR OPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may cause someminor changes in door operationrequiring some re-adjustments,particu

33HAVING A PROBLEM?1. My door will not close and the light bulbs blink onmy motor unit: The safety reversing sensor must beconnected and aligned corre

34Installed Safety Reversing SensorKGKGLED or Diagnostic LED"Learn" Button DiagnosticsLocated On Motor UnitSafety Reversing SensorYour garag

35*3-Button RemotesIf provided with your garagedoor opener, the large buttonis factory programmed tooperate it. Additional buttonson any Security✚®3-B

361. Enter a four digit personalidentification number (PIN) of yourchoice on the keypad. Then pressand hold ENTER.2. While holding the ENTER button,pr

37710125NOTICE6491381LOCKLIGHT11UPCEILING MOUNT ONLY3224681753Installation PartsREPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DESCRIPTION1 81C275 Rac

38Motor Unit Assembly Parts2111358746a6121314141099aKEY PARTNO. NO. DESCRIPTION1 31C568 Drive shaft cover2 41B4245 Line cord3 30B620 Capacitor – 1/2 H

39ACCESSORIES LOCKLIGHTCLOSEDOPENCLLAD41A5281956D953D935CB3-Button Security✚®Remote Control:Includes visor clip.3-Button Mini-Remote Control withSecur

Safety Reversing SensorHorizontal and vertical reinforcementis needed for lightweight garage doors(fiberglass, steel, aluminum, door withglass panels,

© 2007, The Chamberlain Group, Inc.114A3330 All Rights ReservedHOW TO ORDERREPAIR PARTSSelling prices will be furnished on request or parts will beshi

Safety Reversing SensorSafety Reversing SensorAccessDoorGap between floorand bottom of door must not exceed 1/4" (6 mm).HeaderBracketDoorBracketS

6Straight DoorArm SectionCurved DoorArm SectionHeader BracketUPCEILING MOUNT ONLYSprocketCouplingRemote ControlVisor Clip TrolleyRail SupportBraces (

7Wing Nut1/4"-20 (2)Carriage Bolt1/4"-20x1/2" (2)HandleNut 5/16"-18 (6)Ring Fastener (3)Clevis Pin5/16"x2-3/4" (1)Insul

8To prevent INJURY from pinching, keep hands and fingersaway from the joints while assembling the rail.WARNINGCAUTIONWARNINGWARNINGASSEMBLY STEP 1Asse

9Assemble the Rail (continued)3. Attach rail support braces to the back rail. Looselyinsert 1/4-20x7/16" hex bolts into the aligned holes ofthe e