Chamberlain HD220 Bedienerhandbuch

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comCONTENTSPreparation ... 1-4Assem

9AssemblySTEP 5 Tighten the chain1. Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley.2. To tighten the chain,

10InstallationIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUC

11InstallationSTEP 1 Determine the header bracket locationTo prevent possible SERIOUS INJURY or DEATH:lHeader bracket MUST be RIGIDLY fastened to stru

12InstallationSTEP 2 Install the header bracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow t

13InstallationSTEP3 Attach the rail to the header bracket1. Align the rail with the header bracket. Insert the clevis pin through the holes in the he

14InstallationSTEP 5 Hang the garage door openerTo avoid possible SERIOUS INJURY from a falling garage door opener, fasten it SECURELY tostructural su

15InstallationSTEP 6 Install the light bulbTo prevent possible OVERHEATING of the end panel or light socket:lUse ONLY A19 incandescent (60W maximum) o

16InstallationSTEP 8 Install the door bracketFiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFOREinstallation of d

17InstallationSTEP 9 Connect the door arm to the trolleyIMPORTANT: The groove on the straight door arm MUST face away from the curved door arm.1. Clos

18InstallationSTEP10 Install the door controlTo prevent possible SERIOUS INJURY or DEATH from electrocution:lBe sure power is NOT connected BEFORE in

1Safety Symbol and Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided it is installed,operated, mai

19InstallationSTEP 11 Wire the door control to the garage door openerHARDWAREInsulated Staple(Not Shown)1. Run the white and red/white wire from the d

20InstallationSTEP 13 Install the Protector System®Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversingsens

21InstallationSTEP 13 Install the Protector System®(continued)OPTION B WALL INSTALLATIONIf additional clearance is needed an extension bracket (not pr

22InstallationSTEP 14 Wire the Safety Reversing SensorsIf your garage already has wires installed for the safety reversing sensors, proceed to page 23

23InstallationSTEP 14 Wire the Safety Reversing Sensors (continued)OPTION B PRE-WIREDINSTALLATION1. Cut the end of the safety reversing sensor wire,

24InstallationSTEP 15 Connect powerTo prevent possible SERIOUS INJURY or DEATH from electrocution or fire:• Be sure power is NOT connected to the open

25InstallationSTEP 16 Aligning the safety reversing sensorsThe door will not close if the sensors have not been installed and aligned correctly.When t

26AdjustmentsIntroductionWithout a properly installed safety reversal system, persons (particularly small children) could beSERIOUSLY INJURED or KILLE

27AdjustmentsSTEP1 Program the TravelWithout a properly installed safety reversal system, persons (particularly small children) could beSERIOUSLY INJ

28AdjustmentsSTEP 2 Test the Safety Reversal SystemWithout a properly installed safety reversal system, persons (particularly small children) could be

2Additional Items You May Need:Survey your garage area to see if you will need any of the following items:n(2) 2X4 PIECES OF WOODMay be used to fasten

29IMPORTANT SAFETYINSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.2. ALWAYS keep remote con

30OperationFeaturesYour garage door opener is equipped with features to provide you with greater control over your garagedoor operation.REMOTE CONTROL

31OperationUsing Your Garage Door OpenerThe garage door opener can be activated through a wall-mounted door control, remote control, orwireless keyles

32OperationTo Erase the MemoryERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES1. Press and hold the learn button on garage door opener until the learn LE

33MaintenanceMaintenance ScheduleEVERY MONTH• Manually operate door. If it is unbalanced or binding, call a trained door systems technician.• Check to

34Diagnostic ChartYour garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage door opener flash the

Contact InformationFor installation and service information call:1-800-528-9131Before calling, please ensure you have installed your safety reversing

3Carton Inventory/Repair PartsYour garage door opener is packaged in one carton which contains the motor unit and all partsillustrated below.Accessori

4Hardware 041A8068Lock Nut 1/4"-20 (4)Self-Threading Screw 1/4"-20x1-3/4" (2)Master Link Clevis Pin 5/16"x1-1/2" Clevis Pin5/

5AssemblySTEP 1 Assemble the rail and trolleyTo prevent INJURY from pinching, keep hands and fingers away from the joints while assembling therail.To

6AssemblySTEP 2 Fasten the rail to the motor unitTo avoid SERIOUS damage to garage door opener, use ONLY the 1/4"-20x1-3/4" self-threadingsc

7AssemblySTEP 3 Install the pulley1. Lay the chain/cable beside the rail, as shown. Grasp the end with the cable loop and passapproximately 12" (

8AssemblySTEP 4 Install the chainTo avoid possible SERIOUS INJURY to finger from moving garage door opener:lALWAYS keep hand clear of sprocket while o