Owner’s Manual Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door after installation. The
INSTALLATION STEP 5Install the Control ConsoleLocate control console within sight of door, at a minimumheight of 5' (1.5 m) where small children
11INSTALLATION STEP 6Install Remote LightThe remote light is designed to plug directly into astandard 120V outlet.1. Install the hinge and latch clips
12INSTALLATION STEP 7Electrical RequirementsTo avoid installation difficulties, do not run theopener at this time.To reduce the risk of electric shock
13INSTALLATION STEP 8Mount the Battery Backup Unit (BBU)(not provided)If the optional 475LM battery backup unit is part of thisinstallation it should
14Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorFac
15DOOR TRACK MOUNT (RIGHT SIDE)IndicatorLightLensLip SensorBracketDoorTrackFLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)IndicatorLightSensorBracketL
16Invisible Light BeamProtection AreaSensorSensorSafety Reversing SensorBell WireBell WireMotor unitSafety Reversing SensorPower Door LockQuick-Connec
17To prevent damage to vehicles, be sure fully open doorprovides adequate clearance.WARNINGCAUTIONWARNINGWARNINGBLACKPURPLEPush and holduntil the door
18ADJUSTMENT STEP 2Setting the ForceThe force setting button is located on the front panel.The force setting measures the amount of forcerequired to o
19ADJUSTMENT STEP 3Test the Safety Reversal SystemTEST• With the door fully open, place a 1-1/2" (3.8 cm) board(or a 2x4 laid flat) on the floor,
2INTRODUCTIONSafety Symbol Review and Signal Word ReviewWhen you see these Safety Symbols and Signal Wordson the following pages, they will alert you
20ADJUSTMENT STEP 5Test Cable Tension MonitorIf your cable tension monitor has been activated the LEDwill blink 9 times.ADJUSTMENT STEP 6Test Power Do
21OPERATION Using Your Garage Door OpenerYour LiftMaster Security✚®opener and hand-held remotecontrol have been factory programmed to a matchingcode w
22Using the Wall-Mounted ControlConsoleTHE LCD MOTION DETECTING CONTROL CONSOLEPress the push bar toopen or close the door.Press again to reversethe d
23CARE OF YOUR OPENERMAINTENANCE SCHEDULEOnce a Month• Manually operate door. If it is unbalanced or binding,call a trained door systems technician.•
24Having a Problem? (Continued)5. The garage door opens and closes by itself:• Be sure that all remote control push buttons are off.• Remove the bell
25Your garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LEDwill flash a number of times then pause si
26*3-Button RemoteIf provided with your garage door opener, the large buttonis factory programmed to operate it. Additional buttons onany Security✚®3-
271. Press and release the purple “learn”button on motor unit. The learnindicator light will glow steadily for 30seconds.2. Within 30 seconds, enter a
281. Press the “learn button” on light untilLED comes ON.2. Activate the garage door using thehand-held remote, wall control orkeyless entry.3. It has
297101165NOTICE814239121314LOCKLIGHTInstallation PartsREPAIR PARTSKEY PARTNO. NO. DESCRIPTION1 398LM LCD motion detecting door controlconsole2 373W 3-
Safety Reversing SensorSafetyReversingSensorTorsion SpringMotor unitWall-mountedControl ConsoleAccess DoorGap between floor and bottom of door must no
30342165KEY PARTNO. NO. DESCRIPTION1 41DJ001 Logic board complete with plate2 41A6118 Absolute Encoder System3 41C168 TransformerKEY PARTNO. NO. DESCR
31LOCKLIGHTCLOSEDOPENACCESSORIES 370LM41A5281377LMExtension Brackets:(Optional) For safety reversingsensor installation onto the wallor floor.Keyless
LIFTMASTER®SERVICE ISON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND SERVICE INFORMATION IS AS NEARAS YOUR TELEPHONE.SIMPLY DIAL OU
4Preparing your Garage Door Before you begin:• Disable locks. • Remove any ropes connected to garage door. • Complete the following test to make sure
52-Conductor Bell WireWhite & White/RedSafety LabelsandLiteratureRemote ControlVisor ClipMounting BracketSECURITY✚®3-Button Remote Control (1) The
ASSEMBLY STEP 1Attach the Collar to the Motor UnitTo avoid installation difficulties, do not run thegarage door opener until instructed to do so.• Loo
7INSTALLATIONINSTALLATION STEP 1Position the Opener1. Close the garage door completely.2. Slide the opener with collar over the end of the torsionbar.
StaplesLock Screw1/4-20 x 1/2" (2)HARDWARE SHOWN ACTUAL SIZEApprox. 3" (7.6 cm)Lock TemplateRollerGarage Door TrackTOPDRILL 5/16"DRILL
WHT/GRNTo release wire, push in tab with screwdriver tipCable Tension Monitor7/16" (11mm)Strip wire 7/16" (11mm)WHT/GRNCable Tension Monitor
Kommentare zu diesen Handbüchern