Chamberlain 3595 Bedienungsanleitung

GARAGE DOOR OPENERModel 3595 3/4 HPFor Residential UseInstall on Sectional Doors ONLYTHIS OPERATOR IS INTENDED FOR USE ONLY WITH I-BEAM RAILS.Owner’s

10Clevis Pin 5/16"x2-3/4"Ring FastenerINSTALLATION STEP 3Attach the Rail to the Header Bracket• Position the opener on the garage floor bel

11INSTALLATION STEP 5Hang the OpenerThree representative installations are shown. Yours maybe different. Hanging brackets should be angled (Figure 1)t

12INSTALLATION STEP 6Install the Door ControlLocate door control within sight of door, at a minimumheight of 5' (1.5 m) where small children cann

TrolleyNOTICEOverhandKnotEmergencyRelease HandleRopeTrolleyRelease Arm13INSTALLATION STEP 7Install the Light • Press the release tabs on both sides of

14INSTALLATION STEP 9Electrical RequirementsTo avoid installation difficulties, do not run the openerat this time.To reduce the risk of electric shock

15Invisible Light BeamProtection AreaSafety Reversing Sensor6" (15 cm) max. above floorSafety Reversing Sensor6" (15 cm) max. above floorINS

16FLOOR MOUNT (RIGHT SIDE)WALL MOUNT (RIGHT SIDE)DOOR TRACK MOUNT (RIGHT SIDE)Indicator lightLensLip SensorBracketDoorTrackSensorBracketExtensionBrack

Invisible Light BeamProtection AreaSafety Reversing SensorSafety Reversing SensorConnect Wire toOpener Quick-Connect TerminalsBell WireBell WireFinish

18Fiberglass, aluminum or lightweight steel garage doors WILLREQUIRE reinforcement BEFORE installation of door bracket.Contact your door manufacturer

19INSTALLATION STEP 12Connect Door Arm to TrolleySECTIONAL DOORS ONLY• Make sure garage door is fully closed. Pull theemergency release handle to disc

INTRODUCTIONSafety Symbol and Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided it is installed, o

20ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which thedoor will stop when moving up or down

21ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the right sidepanel of the motor unit. Force adjustment settings regulatet

22Without a properly installed safety reversal system, persons(particularly small children) could be SERIOUSLY INJURED orKILLED by a closing garage do

OPERATION 23IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNINGWARNINGWARNINGWARNING1. READ AND FOLLOW ALL WARNINGS ANDI

24Using the Wall-Mounted Door ControlTHE SMART CONTROL PANEL™Press the push bar toopen or close thedoor. Press again toreverse the doorduring the clos

TroubleshootingReduced proximitysensing (does notactivate bytouching top ofremote control)Check if proximity lighting isdisabled by pressing a button.

CARE OF YOUR GARAGE DOOROPENERLIMIT AND FORCE ADJUSTMENTS:Weather conditions may causesome minor changes in dooroperation requiring some readjustments

Having a Problem? (Continued)5. Opener noise is disturbing in living quarters ofhome:• If operational noise is a problem because of proximity ofthe op

Meaning: This message will appear if the Safety Reversing Sensors are out ofalignment, if they are blocked or if the wiring is disconnected. To clear

To Add or Reprogram a Hand-held Remote ControlUSING THE “LEARN” BUTTON USING THE SMART CONTROL PANEL™PROGRAMMING*3-Button RemotesIf provided with your

3To prevent damage to garage door and opener:• ALWAYS disable locks BEFORE installing and operating theopener. • ONLY operate garage door opener at 12

301. Press and release the “learn” buttonon motor unit. The learn indicator lightwill glow steadily for 30 seconds.2. Within 30 seconds, enter a four

31811126NOTICEUPCEILING MOUNT ONLY971013143421LOCKLIGHT5134 652REPAIR PARTSRail Assembly PartsKEY PARTNO. NO. DESCRIPTION1 4A1008 Master link kit2 41A

Motor Unit Assembly Parts32DNDNUPUPBrownWire(Down)ContactLIMIT SWITCH ASSY.GreyWireYellowWire(Up)ContactCenter LimitContactDriveGear3542116209A1861910

33LOCKLIGHTCLOSEDOPENACCESSORIES 915LM1702LM Outside Quick Release:Required for a garage with NO accessdoor. Enables homeowner to opengarage door manu

34NOTES

35NOTES

©2007, The Chamberlain Group, Inc.114A3404B All Rights ReservedLIFTMASTER®SERVICE ISON CALLOUR LARGE SERVICE ORGANIZATIONSPANS AMERICAINSTALLATION AND

Safety Reversing SensorSupport bracket & fastening hardwareis required.See page 11. — — — — — — — —Header WallFINISHED CEILINGTorsio

5UPCEILING MOUNT ONLYChassis SupportBracketChain SpreaderExtensionBracket (2)RailChain Pulley BracketChainStraight DoorArm SectionCurved Door Arm Sect

Washered Bolt 5/16"-18x1/2"Lock Nut6ASSEMBLY STEP 1Attach the Rail to the Motor UnitTo avoid installation difficulties, do not run the garag

7ASSEMBLY STEP 4Tighten the Chain• Spin the inner nut and lock washer down the threadedshaft, away from the trolley.• To tighten the chain, turn outer

8INSTALLATION STEP 1Determine the Header BracketLocationSECTIONAL DOOR ONLY1. Close the door and mark the inside vertical centerline ofthe garage door

9INSTALLATION STEP 2Install the Header BracketYou can attach the header bracket either to the wall abovethe garage door, or to the ceiling. Follow the