Chamberlain PD432DM Bedienungsanleitung

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comGARAGE DOOR OPENERModel PD432DM 1/2 HPFor Residential Use O

10HARDWARE SHOWN ACTUAL SIZEHex Bolt 1/4"-20x7/16"ASSEMBLY STEP 2Fasten the Rail to the Motor Unit and Install the TrolleyNOTE: To aid in as

11ASSEMBLY STEP 3Attach the Rail Brackets• Align rail brackets to end of rail assembly, as shown. • Insert two 1/4"-20x7/16" hex bolts.

12INSTALLATION STEP 1Determine the Header Bracket LocationInstallation procedures vary according to garage door types. Follow the instructions which a

13Garage Door - Finished Ceiling -The nail hole is for positioning only. You must use lag screws to mount the header bracket.Ceiling Mounting HolesVe

14INSTALLATION STEP 3Attach the Rail to the Header Bracket• Position the opener on the garage fl oor below the header bracket. Use packing material a

15INSTALLATION STEP 4Install The Protector System®The safety reversing sensor must be connected and aligned correctly before the garage door opener wi

16INSTALLING THE BRACKETSBe sure power to the opener is disconnected. Install and align the brackets so the sensors will face each other across the ga

17MOUNTING AND WIRING THE SAFETY SENSORS• Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. Use wing nuts to fasten se

18To prevent damage to garage door, rest garage door opener rail on 2x4 placed on top section of door.Door 2x4 is used to determine the correct mounti

19INSTALLATION STEP 6Hang the OpenerThree representative installations are shown. Yours may be different. Hanging brackets should be angled (Figure 1)

2TABLE OF CONTENTSWhen you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury

20INSTALLATION STEP 7Install the Door ControlLocate door control within sight of door at a minimum height of 5 feet (1.5 m) where small children canno

21INSTALLATION STEP 8Install the Lights • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is

22INSTALLATION STEP 10Electrical RequirementsTo avoid installation diffi culties, do not run the opener until Step 11 below.To reduce the risk of elect

23HARDWARE SHOWN ACTUAL SIZESelf-Threading Screw 1/4"-14x5/8"Figure 1HORIZONTAL AND VERTICALREINFORCEMENT IS NEEDED FOR LIGHTWEIGHT GARAGE D

24HARDWARE SHOWN ACTUAL SIZESelf-Threading Screw 1/4"-14x5/8"METAL DOORFinished Ceiling WOOD DOORSelf-Threading Screw 1/4"-14x5/8"

25Straight Door ArmStraight Door ArmCurved Door ArmCurved Door Arm(Groove facing out)CORRECT INCORRECTNuts5/16"-18Lock Washers5/16"Bolts5/16

26ALL ONE-PIECE DOORS1. Assemble the door arm, Figure 5:IMPORTANT: The groove on the straight door arm MUST face away from the curved door arm (Figur

27ADJUSTMENT STEP 1Adjust the UP and DOWN Travel LimitsLimit adjustment settings regulate the points at which the door will stop when moving up or dow

28ADJUSTMENT STEP 2Adjust the ForceForce adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the a

29ADJUSTMENT STEP 3Test the Safety Reversal SystemTEST• With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid fl at) on the fl o

3Tools neededDuring assembly, installation and adjustment of the opener, instructions will call for hand tools as illustrated below.To prevent possibl

30OPERATIONIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:WARNING 1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.2

31Using the Wall-Mounted Door ControlTHE MULTI-FUNCTION DOOR CONTROLPress the lighted push button to open or close the door. Press again to reverse th

32MAINTENANCE SCHEDULEEvery Month• Manually operate door. If it is unbalanced or binding, call a trained door systems technician.• Check to be sur

33KGKGSending Eye Safety Reversing Sensor (Amber Indicator Light)Receiving Eye Safety Reversing Sensor (Green Indicator Light)“Learn” Button LED or

34KGKGYour garage door opener is programmed withself-diagnostic capabilities. The “Learn” button/diagnostic LED will fl ash a number of times then paus

35KG13975KG13975LOCKLIGHT*3-Button Remotes (315 MHz)If provided with your garage door opener, the large button is factory programmed to operate it. Ad

36LOCKLIGHT1. Enter a four digit personal identifi cation number (PIN) of your choice on the keypad. Then press and hold ENTER.2. While holding the

37REPAIR PARTSNOTICELOCKLIGHTUPCEILING MOUNT ONLYKEY PART NO. NO. DESCRIPTION1 81C275 Rack2 41A6263 Hardware bag (includes sprocket coupling)3

38Motor Unit Assembly Parts123456a6712111314149109a8KEY PART NO. NO. DESCRIPTION 1 31C568 Drive shaft cover 2 41B4245 Line cord 3 30B620

39ACCESSORIES 953D3-Button SECURITY✚® Remote Control :Includes visor clip.LOCKLIGHTMotion Detecting Control Panel:Multi-function door control with mot

4PlanningIdentify the type and height of your garage door. Survey your garage area to see if any of the conditions below apply to your installation. A

CHAMBERLAIN® SERVICE IS ON CALLOUR LARGE SERVICE ORGANIZATION SPANS AMERICAINSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE.SIMPLY DI

5Planning (Continued) ONE-PIECE DOOR INSTALLATIONS• Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer t

6Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model

7INSTALLATION HARDWARECarriage Bolt 1/4"-20x1/2" (2)Lag Screw 5/16"-9x1-5/8" (2)Lag Screw 5/16"-18x1-7/8" (2)Drywall Anc

8To prevent INJURY from pinching, keep hands and fi ngers away from the joints while assembling the rail.ASSEMBLY STEP 1Assemble the RailTo avoid insta

9Assemble the Rail (continued)3. Attach rail support braces to the back rail. Loosely insert 1/4-20x7/16" hex bolts into the aligned holes of t