Chamberlain HD210 Bedienerhandbuch

The Chamberlain Group, Inc.845 Larch AvenueElmhurst, Illinois 60126-1196www.chamberlain.comCONTENTSPreparation ... 1-4Assem

9AssemblySTEP 5 Tighten the chain1. Spin the inner nutand lock washer down the trolleythreaded shaft, away from the trolley.2. To tighten the chain, t

10InstallationIMPORTANT INSTALLATION INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL INSTALLATION WARNINGS AND INSTRUC

11InstallationSTEP 1 Determine the header bracket locationTo preventpossible SERIOUS INJURY or DEATH:l Header bracketMUSTbe RIGIDLY fastened to struct

12InstallationSTEP 2 Install the header bracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow t

13InstallationSTEP 3 Attach the rail to the header bracket1. Position the opener on the garage floor below the header bracket. Use packing material as

14InstallationSTEP 5 Hang the garage door openerTo avoid possible SERIOUS INJURY from a falling garage door opener,fasten it SECURELY tostructural sup

15InstallationSTEP 6 Install the light bulbTo preventpossible OVERHEATING of the endpanel or lightsocket:l DO NOT use shortneck or specialtylight bulb

16InstallationSTEP 8 Install the door bracketFiberglass, aluminum or lightweightsteel garage doors WILL REQUIRE reinforcement BEFOREinstallation of do

17InstallationSTEP 8 Install the door bracket (continued)OPTION B ONE-PIECE DOORS1. Center the door bracket on the top ofthe door, in line with the he

18InstallationSTEP 9 Connect the door arm to the trolleyInstallation will vary according to the garage door type. Followthe instructions which apply t

1Safety Symbol and Signal Word ReviewThis garage door opener has been designed and tested to offer safe service provided it is installed,operated, mai

19InstallationSTEP 9 Connect the door arm to the trolley (continued)OPTION B ONE-PIECE DOORSIMPORTANT: The groove on the straight door arm MUSTface aw

20InstallationSTEP10 Install the door controlTo preventpossible SERIOUS INJURY or DEATHfrom electrocution:l Be sure power isNOT connected BEFORE inst

21InstallationSTEP 11 Wire the door control to the garage door openerHARDWAREInsulated Staple(Not Shown)1. Run the white and red/white wire from the d

22InstallationSTEP 13 Install the Protector System®Be sure power isNOT connected to the garage door opener BEFORE installing the safetyreversingsensor

23InstallationSTEP 13 Install the Protector System®(continued)OPTION B WALL INSTALLATIONIf additional clearance is needed an extension bracket (notpro

24InstallationSTEP 14 Wire the Safety Reversing SensorsIf your garage already has wires installed for the safetyreversing sensors,proceed to page 25.H

25InstallationSTEP 14 Wire the Safety Reversing Sensors (continued)OPTION B PRE-WIRED INSTALLATION1. Cutthe end of the safetyreversing sensor wire, ma

26InstallationSTEP 15 Connect powerTo preventpossible SERIOUS INJURY or DEATHfrom electrocution or fire:l Be sure power isNOT connected to the opener,

27InstallationSTEP 16 Aligning the safety reversing sensorsThe door will not close if the sensors have not been installed and aligned correctly.When t

28AdjustmentsIntroductionWithout a properlyinstalled safetyreversal system,persons (particularlysmall children) could beSERIOUSLY INJURED or KILLED by

2Additional Items You May Need:Surveyyour garage area to see if you will need any of the following items:n (2) 2X4 PIECES OF WOODMaybe used to fasten

29AdjustmentsSTEP 1 Program the TravelWithout a properlyinstalled safetyreversal system,persons (particularlysmall children) could beSERIOUSLY INJURED

30AdjustmentsSTEP 2 Test the Safety Reversal SystemWithout a properlyinstalled safetyreversal system,persons (particularlysmall children) could beSERI

31IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of SEVERE INJURY or DEATH:1. READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.2. ALWAYS keep remote con

32OperationFeaturesYour garage door opener is equipped with features to provide you with greater control over your garagedoor operation.TIMER-TO-CLOSE

33OperationUsing your Garage Door OpenerThe garage door opener can be activated through a wall-mounted door control, remote control, orwirelesskeyless

34OperationTo Erase the MemoryERASE ALL REMOTE CONTROLS AND KEYLESS ENTRIES1. Press and hold the LEARNbutton on garage door opener until the learn LED

35MaintenanceMaintenance ScheduleEVERY MONTHl Manuallyoperate door. Ifit is unbalanced or binding,call a trained door systemstechnician.l Check to be

36Diagnostic ChartYour garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrowson the garage door opener flash the d

37DIAGNOSTIC CODE SYMPTOM SOLUTIONUp Arrow Flash(es)Down Arrow Flash(es)4 1-4Door is moving stops or reverses. Manuallyopen and close the door. Checkf

38AccessoriesAGDMEVCLLP1953EVCLSS1940EV956EVGarage Door and Gate Monitor:Monitor open/closed status for up to 4 compatible garage door openers and clo

3Carton InventoryYour garage door opener is packaged in one carton which contains the motor unit and all partsillustrated below. Accessories vary depe

39WarrantyCHAMBERLAIN® LIMITED WARRANTYThe Chamberlain Group, Inc.® (“Seller”) warrants to the fi rst retail purchaser of this product, for the residen

Repair PartsRail Assembly PartsAccessories324651Description Part Number1 Chain and Cable 41A58072 Pulley 144C563 Master Link 4A10084 Rail 41A56655 Tro

Repair PartsGarage Door Opener PartsDescription Part Number1Chain Spreader 41A56152Gear and Sprocket 41C4220A3Drive and Worm Gear 41A28174Front End P

42Notes

© 2015, The Chamberlain Group, Inc.114A4835B All Rights Reserved

4HardwareBolt 1/4"-20x1-3/4" Lock Nut 1/4"-20BoltNut 3/8" Lock Washer 3/8"Master Link Clevis Pin 5/16"x1-1/2" Ring

5AssemblySTEP 1 Assemble the rail and install the trolleyTo preventINJURY from pinching, keep hands and fingersawayfrom the joints while assembling th

6AssemblySTEP 2 Fasten the rail to the motor unitTo avoid SERIOUS damage to garage door opener,use ONLY those bolts/fasteners mounted in thetop of the

7AssemblySTEP 3 Install the idler pulley1. Laythe chain/cable beside the rail,as shown. Grasp the end of the cable and passapproximately 12" (30

8AssemblySTEP 4 Install the chainTo avoid possible SERIOUS INJURY to finger from moving garage door opener:l ALWAYS keep hand clear of sprocket while